How do you actually feel when it comes to Installing A Bathtub?
Installing a tub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is conveniently accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified yourself for the task and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your shower room if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your tools and also product list ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using both wood boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leaks as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The former type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, creating the water to permeate the wall surface between the bath as well as the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub? Try to leave a remark down the page. We'd be pleased to see your responses about this entry. Hoping that you come back again before long. Remember to set aside a second to distribute this write-up if you enjoyed reading it. Thanks a lot for your time. Please pay a visit to our website back soon.
Book 24/7